• <td id="c96yt"></td>

    <tr id="c96yt"><s id="c96yt"><tt id="c96yt"></tt></s></tr>

    <td id="c96yt"></td>

    <p id="c96yt"><label id="c96yt"><xmp id="c96yt"></xmp></label></p>
    <td id="c96yt"><option id="c96yt"></option></td>
  • <pre id="c96yt"></pre>

    banner

    高溫浸滲劑

    • 分類:浸滲劑
    • 發布時間:2022-01-12 09:05:07
    • 訪問量:0
    概要:
    概要:
    詳情

    HY-90G浸滲劑主要用來封堵金屬鑄件內部泄漏性微孔、砂眼或隙縫,使這些泄漏性不良產品重新成為合格可使用產品;HY-90G浸滲劑也可用于各種粉末冶金件(金屬燒結體)的封孔、電鍍效果改良和機加工處理。在材料改良領域里屬不可缺少的處理技術。 無機浸滲劑成本低,操作簡單,耐高溫性好。

    HY-90G infiltrant is mainly used to block leaking micropores, blisters or gaps in metal castings, so that these poor leaking products can be used again as qualified products; HY-90G infiltrant can also be used for various powder metallurgy parts (Metal sintered body) sealing, electroplating effect improvement and machining. It is an indispensable processing technology in the field of material improvement. The inorganic impregnating agent has low cost, simple operation and good high temperature resistance.

     

     

     

    基本參數  

    主要成分

    硅酸鹽

    處理工藝

    真空-浸滲-清洗-固化

    粘度(mPa.s)

    >35

    清洗性

    一般

    pH

    >10.0

    固體成分

    35-45%

    耐熱性

    MAX: 600 (℃)

    浸滲效果

    僅限于50-100μm微孔,效果不如有機浸滲劑

    保管方法

    常溫、避光

    技術參數

     

     密度(g/cm3)

    1.38-1.40

    溶解性

    能溶于水

    固化方式

    常溫,干燥

    固化溫度(℃)

    95/干燥

    固化時間(min)

    120/干燥

    有效封孔直徑(μm)

    40~80

    保存條件(℃)

    常溫

    保存期(mon) 12
     

     

     

    ZH—101A型浸滲液,是一種高分子化學填料,添加金屬氧化物(例如:硅、鋁、鈦、鎂、銅和鐵的氧化物)。通過加溫實現固化,最終在微孔內形成一種100﹪熱固化填料,其特點是低粘度高浸透性,低收縮率密封合格率達98﹪以上,耐化學介質,耐溫性能優良、耐溫在-50---1300℃,有色和黑色金屬鑄件,在鑄造過程中易產生氣孔、縮孔和疏松等缺陷。這些微小的氣孔如果壁厚方向連通起來,鑄件在受氣壓或液壓作用時會形成泄漏,導致產品報廢,通過本廠設計的CS系列浸滲設備和浸滲液,對微孔缺陷在孔徑0.5㎜以下的承壓件,浸滲合格率在98﹪以上給廠家降低成本。

    ZH-101A type impregnating liquid is a polymer chemical filler, adding metal oxides (such as oxides of silicon, aluminum, titanium, magnesium, copper and iron). It is cured by heating, and finally a 100% heat-curing filler is formed in the micropores, which is characterized by low viscosity, high permeability, low shrinkage rate and sealing qualification rate of more than 98%, chemical resistance, excellent temperature resistance, and resistance to The temperature is -50 ℃---1300 ℃, non-ferrous and ferrous metal castings are prone to defects such as pores, shrinkage holes and porosity during the casting process. If these tiny pores are connected in the direction of wall thickness, the castings will leak when subjected to air pressure or hydraulic pressure, resulting in product scrapping. Through the CS series impregnation equipment and impregnation liquid designed by our factory, the diameter of micropore defects is 0.5mm. For the following pressure-bearing parts, the impregnation pass rate is above 98% to reduce the cost of the manufacturer.

    特點Features:

    1.  操作簡單、效率高,45分鐘可完成一個浸滲流程。

    2.     100﹪反應固化不收縮,固化物堅韌耐老化,乃化學介質優良。

    3.     容易清洗,不影響工作表面精度,不腐蝕金屬對操作人員及環境完全無害。

    4.     鑄件在電鍍、噴漆前浸滲,可延長零件壽命,是表面處理質量優良。

    5.     與泡化堿及合成樹脂成本比較,雖然泡化堿及合成樹脂的材料費,只是熱固化浸滲的幾分之一但綜合比較,報廢鑄件成本能調消耗,因極大提高效率節省的工是成本,用熱固化浸滲工藝將其成本大大降低。

    1. Simple operation and high efficiency, one impregnation process can be completed in 45 minutes.

    2. 100% reaction curing does not shrink, the cured product is tough and resistant to aging, and it is an excellent chemical medium.

    3. It is easy to clean, does not affect the accuracy of the working surface, and does not corrode the metal, which is completely harmless to the operator and the environment.

    4. The castings are impregnated before electroplating and painting, which can prolong the life of the parts and have excellent surface treatment quality.

    5. Compared with the cost of soaking alkali and synthetic resin, although the material cost of soaking alkali and synthetic resin is only a fraction of that of thermal curing infiltration, comprehensive comparison, the cost of scrap castings can be adjusted and consumed, because the efficiency is greatly improved. The labor is the cost, and the cost is greatly reduced by the thermal curing impregnation process.

    主要性能Main performance:

    1.  粘結力和強度較高。

    粘膠劑硬化后的主要成分為硅凝膠,比表面積大,因而有較高的粘結里。

    2.      耐酸性好

    可以抵抗除氫 酸(HF)熱磷酸的高級脂肪酸以外的,幾乎所有無機的有機酸。

    3.      耐熱性好

    硬化后形成的二氧化硅在高溫下強度提高的熱度可達1000度以上。

    4.      注意事項

    本品如進入眼睛、誤食,盡量用大量的清水清洗,嘔吐并立即就醫,如接觸皮膚用水洗即可。

          浸滲液又稱浸滲劑,也稱含浸劑、封孔劑、浸滲膠,主要用來封堵金屬鑄件內部泄漏性微孔、砂眼或隙縫,使這些泄漏性不良產品重新成為合格可使用產品;浸滲劑也可用于各種粉末冶金件(金屬燒結體)的封孔、電鍍效果改良和機加工處理。在材料改良領域里屬不可缺少的處理技術。 無機浸滲劑成本低,操作簡單,耐高溫性好。

    浸滲劑主要性能:
    主要成分  硅酸鹽) 
    處理工藝  真空-加壓-清洗-固化 
    粘度(mPa.s) 35
    清洗性  良好 
    pH
    10.0
    固體分  45-55%
    耐熱性  MAX 600 (℃) 
    浸滲效果 僅限于0.1-0.15微孔,使用成本  低于有機浸滲劑 
    保管方法  常溫、避光 
    密度 1.4-.145
    溶解性 易溶于水
    固化方式 常溫固化,烘干固化
    封孔直徑 0.1-0.5mm
    保存條件 室溫
    保存期限 二年

    本公司生產的浸滲劑具備以下特點: 
    ※ 
    浸滲效果非常出色,工件合格率都在96%以上 
    ※ 
    水洗性非常好,任何復雜的工件都不存在紋孔殘留堵塞的問題 
    ※ 
    可用于所有類型工件的浸滲處理 
    ※ 
    浸滲后工件耐久性非常好 
    ※ 
    粘度極低,同樣條件下消耗量最少
    使用范圍:
    汽車零部件:發動機缸體、缸蓋、油泵體、水泵座、空調壓縮機缸體、缸蓋、進氣岐管、轉向器、 
    變速箱、軸承箱、化油器等 
    管件閥件:各種民用和工業設備用氣管、水管和閥件 
    粉末冶金件(燒接體):各種金屬粉末冶金件的封孔、電鍍改良、機加工改良等

    1. High adhesion and strength.

    The main component of the adhesive after hardening is silica gel, which has a large specific surface area and thus has a high bonding strength.

    2. Good acid resistance

    It can resist almost all inorganic organic acids except higher fatty acids such as hydrogen acid (HF) hot phosphoric acid.

    3. Good heat resistance

    The silica formed after hardening can increase its strength at high temperature by more than 1000 degrees.

    4. Notes

    If this product gets into eyes or ingested by mistake, try to wash with plenty of water, vomit and seek medical attention immediately.

    Impregnation liquid, also known as impregnating agent, also known as impregnating agent, sealing agent, impregnating glue, is mainly used to block leaking micropores, blisters or gaps in metal castings, so that these leaky products can be used again. Products; impregnating agents can also be used for sealing holes, improving electroplating effects and machining of various powder metallurgy parts (metal sintered bodies). It is an indispensable processing technology in the field of material improvement. The inorganic infiltrant has low cost, simple operation and good high temperature resistance.

    The main properties of the impregnant:
    Main ingredient Silicate)
    Treatment Process Vacuum-Pressure-Cleaning-Curing
    Viscosity (mPa.s) >35
    good cleaning
    pH >10.0
    Solid content 45-55%
    Heat resistance MAX: 600 (℃)
    The infiltration effect is limited to 0.1-0.15 micropores, and the cost of use is lower than that of organic infiltrators
    Storage method Room temperature, dark
    Density 1.4-.145
    Solubility easily soluble in water
    Curing method Room temperature curing, drying curing
    Sealing diameter 0.1-0.5mm
    Storage conditions Room temperature
    Shelf life two years

    The impregnating agent produced by our company has the following characteristics:
    ※ The infiltration effect is very good, and the pass rate of the workpiece is above 96%
    ※ The washability is very good, and there is no problem of residual blockage of pits for any complex workpiece.
    ※ Can be used for impregnation treatment of all types of workpieces
    ※ The durability of the workpiece after impregnation is very good
    ※ Very low viscosity, minimum consumption under the same conditions
    Scope of use:
    Auto parts: engine block, cylinder head, oil pump body, water pump seat, air conditioning compressor cylinder block, cylinder head, intake manifold, steering gear,
    Gearbox, bearing housing, carburetor, etc.
    •Pipe fittings and valves: air pipes, water pipes and valves for various civil and industrial equipment
    • Powder metallurgy parts (sintered body): sealing, electroplating improvement, machining improvement of various metal powder metallurgy parts, etc.

     

     

      臺州市浸滲化工機械設備廠

      電話:0576-82640565  13867654976

     

    本司將致力于不斷的改進產品生產工藝和品質,并且不斷的發展新的產品去保持市場的競爭能力。正朝著現代企業的方向與時間一同前進。以“真誠、務實、優質、高效”為企業宗旨,竭誠為各界人士服務。

    The company will continue to improve the production process and quality of products, and continue to develop new products to maintain market competitiveness. Is moving in the direction of the modern enterprise with time. "Sincere, pragmatic, high quality, efficient" for the purpose of the enterprise, dedicated to serve people from all walks of life.

    頭尾

    發布時間:2022-01-11 20:01:23

    地       址:浙江省臺州市路橋區蓬街鎮蓬街工業園區

    客服熱線:0086-576-82640565

    客服郵箱:zkjssb@126.com

    ? 2022 臺州亨旭浸滲設備有限公司 Taizhou Hengxu Infiltration Equipment Co.,Ltd.  浙ICP備2022002778號  網站建設:中企動力 臺州

    刺激久久亚洲中文_国内a片xxxxx_2018a片免费看_日本新黄色网站入口

  • <td id="c96yt"></td>

    <tr id="c96yt"><s id="c96yt"><tt id="c96yt"></tt></s></tr>

    <td id="c96yt"></td>

    <p id="c96yt"><label id="c96yt"><xmp id="c96yt"></xmp></label></p>
    <td id="c96yt"><option id="c96yt"></option></td>
  • <pre id="c96yt"></pre>